SIEL DK70 Manual - MIDI cc messages

start - tips - pictures - signal flow - presets - repair dead keys | apps: patch editor - sysx analyzer | midi: sysx structure - cc messages - BCF2000

Mapping for the DK70

I mapped the CC messages to the Behringer BCF2000.
blue: fader, green: button, purple: rotary

Parameter Function MIDI CC Range BCF2000
01 DEG VCA-A Attack 12 0 ~ 15 Rotary 3.1
02 DEG VCA-A Decay 13 0 ~ 15 Rotary 3.2
03 DEG VCA-A Breakpoint 14 0 ~ 15 Rotary 3.3
04 DEG VCA-A Slope 15 0 ~ 15 Rotary 3.4
05 DEG VCA-A Sustain 16 0 ~ 15 Rotary 3.5
06 DEG VCA-A Release 17 0 ~ 15 Rotary 3.6
07 DEG VCA-A Damper 19 0 (Off) ~ 1 (On)  
08 DCO Mode 20 1 (Whole) ~ 2 (Double)  
Parameter Function MIDI CC Range  
11 DEG VCA-B Attack 21 0 ~ 15 Rotary 4.1
12 DEG VCA-B Decay 22 0 ~ 15 Rotary 4.2
13 DEG VCA-B Breakpoint 23 0 ~ 15 Rotary 4.3
14 DEG VCA-B Slope 24 0 ~ 15 Rotary 4.4
15 DEG VCA-B Sustain 25 0 ~ 15 Rotary 4.5
16 DEG VCA-B Release 26 0 ~ 15 Rotary 4.6
17 DEG VCA-B Damper 28 0 (Off) ~ 1 (On)  
Parameter Function MIDI CC Range  
21 Detune Interval 29 0 ~ 61 Fader 1.4
22 Detune Fine ** 30 0 ~ 15 Fader 1.5
23 Noise Level 31 0 ~ 15 Fader 1.6
24 Noise Destination 32 1 (VCA) ~ 2 (VCF)  
Parameter Function MIDI CC Range  
31 DEG VCF Attack 33 0 ~ 15 Rotary 2.1
32 DEG VCF Decay 34 0 ~ 15 Rotary 2.2
33 DEG VCF Breakpoint 35 0 ~ 15 Rotary 2.3
34 DEG VCF Slope 36 0 ~ 15 Rotary 2.4
35 DEG VCF Sustain 37 0 ~ 15 Rotary 2.5
36 DEG VCF Release 38 0 ~ 15 Rotary 2.6
Parameter Function MIDI CC Range  
41 LFO-2 Frequency 40 0 ~ 15  
42 LFO-2 Final Level 41 0 ~ 15  
43 LFO-2 Initial Level 42 0 ~ 15  
44 LFO-2 Delay Time 43 0 ~ 15  
45 LFO-2 Delay Mode 44 1 (Manual), 2 (Auto)  
46 LFO-2 Waveform 45 1 (Triangle), 2 (Square)  
Parameter Function MIDI CC Range  
51 LFO-1 Frequency 46 0 ~ 15 Rotary 1.5
52 LFO-1 Final Level 47 0 ~ 15 Rotary 1.8
53 LFO-1 Initial Level 48 0 ~ 15 Rotary 1.7
54 LFO-1 Delay Time 49 0 ~ 15 Rotary 1.6
55 LFO-1 Delay Mode 50 1 (Manual), 2 (Auto)  
Parameter Function MIDI CC Range  
62 DCO Waveform 51 0 (Off), 1 (Sqr), 2 (Saw)  
63 DCO Sawtooth Octave 52 1 (16'), 2 (8'), 3 (4')  
64 DCO Square 16' Level 53 0 ~ 15 Rotary 1.1
65 DCO Square 8' Level 54 0 ~ 15 Rotary 1.2
66 DCO Square 4' Level 55 0 ~ 15 Rotary 1.3
67 DCO Square 2' Level 56 0 ~ 15 Rotary 1.4
Parameter Function MIDI CC Range  
71 VCF Cutoff 57 0 ~ 99 Fader 1.1
72 VCF Resonance 58 0 ~ 15 Fader 1.2
73 VCF Keyboard Track 59 0 (Off), 1 (Half), 2 (Full)  
74 VCF DEG Trigger Mode 60 1 (Single), 2 (Multi)  
75 VCF DEG Level 61 0 ~ 15 Fader 1.3
Parameter Function MIDI CC Range  
81 Chorus ** 62 0 (Off), 1 (On)  
82 Volume 63 0 ~ 15 Fader 1.8

Thank you http://www.emismusic.co.uk/museum/Siel/EX80/SielExpander80.htm

** [CC30, CC62] There seems to be a bug in the MIDI controller reception with the Expander 80, unless there ever was an operating system update, Parameter 22 (Detune Fine) and Parameter 81 (Chorus) cannot be controlled by their associated controllers (CC30 and CC62). When receiving MIDI CC30, the Expander 80's display changes to show the incoming data, but the actual detuning (chorus speeed) does not change, same with CC62. Maybe this was corrected in a software revision.

*** [64] MIDI Controller 65 is the Manual LFO trigger control, this is a hang over from the DK80 keyboard version, that had a trigger switch (rather than a mod wheel). Controller 65 is usually the second pedal function (although perhaps the standard controller CC1 would have made more sense - never mind.....)

The Expander 80 also responds to controller 125 (Omni On), controller 124 (Omni Off) and controller 123 (All Notes Off).

copyright: tinyloops.com - contact